Wooden Toys have a slightly different set of equipment than soft toys due to the different tests in them, so i figured they deserved their own blog post 🙂
Some of the equipment is worth investing in to keep, as it can be used for more than one test, and once you have it you can use it for testing repeated toys. I kitted myself out for testing at around £40 for all, some things you may already have around the house or shed.
So here’s some essentials:
A Newton or Luggage meter: For testing torque and tension, a luggage weighing meter will do the same job but you may need to do a conversion for the amount of newtons to weight (google does a good job of this)
An S hook : This may not be necessary, but may be useful for hanging the bags for the tensions tests, if you arn’t using the newton meter for the equivalent.
A sturdy bag for carrying the tension weights (supermarket woven type works fine)
A 1kg 80mm weight – I have racked my brains for an alternative but this is pretty much one of those things which is really hard to do an alternative version of to be as close to the standards as possible. It is very specific. So for this we recommend Ebay’s ‘Steel2go’ for an 80mm diameter, 25mm length steel rod, which comes up to the 1kg -/+ 2g pretty much exactly.
https://www.ebay.co.uk/itm/Bright-Mild-Steel-Round-Bar-55mm-to-100mm-Dia-EN3B-Rod-25mm-to-500mm-Long/291774055803?var=590787210816&hash=item43ef16c57b:g:YgQAAOSwvQdcyr3u
Tape measure or Meter stick – for measuring heights for the drop test and impact test
A guiding tube – I used an acrylic tube from ebay, it needs to be wide enough to guide the weight down consistently, but not restrict the fall. You could easily make one from cardboard. 
A steel plate – This is for both the drop and impact tests, but you may feel under due diligence that you have an equivalent hard or harder surface – do some googling over the hardness of the surface and always ensure you are over testing rather than under testing.
A 75a shore hardness rubber mat 2mm- This will protect your sample from damage in the drop, impact and compression test.
https://www.ebay.co.uk/itm/HIGH-TEMPERATURE-FUEL-CHEMICAL-RESISTANT-VITON-RUBBER-SHEET-1MM-6MM-THICK/371731267604?ssPageName=STRK%3AMEBIDX%3AIT&var=640712278703&_trksid=p2057872.m2749.l2649
A disk weight/plate 30mm – Should your toy have curves and not be able to test all areas with the impact tests, you will need to do the compression tests. You can buy these from ebay, alternatives would be a 3cm dog tag perhaps.
https://www.ebay.co.uk/itm/MILD-STEEL-SQUARE-or-ROUND-Disc-Plate-Sheet-Metal-Laser-Cut-Washer-Blank/362829285374?hash=item547a4f87fe:g:OkkAAOSwOCxfDxhB
A dowel/rod – For the compression tests to attach to the disk weight, I used a sawn off rolling pin, a dowel or broom handle will also work.
Bathroom scales – digital which can weigh in kilos saves some effort in converting weights for the compression test
Demineralised water – This is used for soak testing to simulate saliva and can be bought very cheaply online:
https://www.surechemicals.co.uk/specialised-products-special-offers/specialised-products/demineralised-water
you will also need a bowl or bucket, and possibly a second with weights to weigh the toy down under the water
Small Parts Cylinder – this comes in our pack in a paper version, but solid versions are available by brands such as safe tots.
Specialised Templates
Should you be making certain types of toys you may need the specialised templates, but most will not need these. Always double check to be sure against the standards and don’t take this blog as gospel – its especially important in these types of toys and you can always check with an accredited lab if you are unsure.
These can currently be bought as guides from:
https://www.theteethingstore.com/product-page/template-a-b-guides
Template A – This is specifically for toys for babies under 10 months, if your toy is designed for little babies in mind , or could be mistaken for a toy for under 10 months in its functions and characteristics, you will need this template. Its designed to test the shape and size of certain toys to avoid impaction in a baby who isn’t sitting up yet.
Template B – This is for testing spherical toys, toys with spherical ends for babies, and also for the play figures test (peg dolls) with spherical heads. If your peg doll is over the size of 64mm it will pass this test, so you do not need a copy of the template itself.
Hopefully this gives you a good idea of what is needed for home testing your wooden toys. Don’t forget we now have an add on to the soft toy pack which outlines the tests in more detail, so let us know if you need it.
