‘Flash’ testing
It’s important to note that toys that a child can enter (teepees, tents etc) and Costumes have their own version of flammability testing, and this is aimed for soft toys only.
What is it?
Flash testing has often been a word thrown about in the past when it comes to flammability but the instructions on how to do it are all rather vague. The standards are not particularly clear on flash testing, but do refer to ‘surface flash’ on pile fabrics which is when there is a rapid flame spread across the fabric which does not set light to its base – a fabric which does this is not safe for toys. It is recommended that the fabric is tested in the same way as a soft filled toy. This surface flash is not the same as we would do for cotton etc fabrics when we use due diligence, but it is useful on how we should perform a test. A flash test in this blog today is a fabric burn rate test done on a sample of fabric.
When can I do a flash test? When can I not do a flash test?
The majority of the time, your toy sample will need a full flammability test. You can’t use a flash test to avoid burning a toy sample – as tempting as it may be(!) Whenever you make a toy with new material compositions, even if it looks the same as your last toy otherwise, it will need a full flammability test.
For example if you made a doll in cottons, you will do a full flammability test on your doll. If you then made that same doll in plush, you will do a full flammability test again because the composition of the fabric is different- ie plush is polyester based, and cotton is natural fibres based, so one will melt(poly/plastic base), and one will burn. The two fabric types can’t be compared on how they might react to a flame. And the same goes for any new other material composition.
If your toy has a different shape, you will do a full flammability test. Its difficult to predict how flame will react to a toy in each different shape..you need to know the flame won’t catch an unexpected part of the toy and burn to the top faster than on a previously tested toy.
So, when can you choose to do a flash test? As usual, as a small time maker it comes down to using due diligence. It’s not cost effective as a small maker to test a doll in every single fabric, in every single pattern. So we use due diligence to show we are doing our best within our means to prove that our toys are safe. This means that we are not strictly sticking to the guidelines as such, but doing our best within our money limit to show compliancy. A flash test is not done to avoid burning a completed toy, it’s about testing small variations in fabrics with the same composition.
So, When you’ve made a doll out of one brand of cotton fabrics(100% cotton) and you want to do another doll the same with 100% cotton from a different manufacturer, then you may choose to do a flash test instead of another full toy burn test.
When you have bought a new fabric and you’re concerned about the burn rate before making your toy, you may choose to do a flash test before making the item – but still perform a full flammability test on a completed toy.
Sizing – If your toy is below the 15cm threshhold for flammability testing, you may use flash testing to test each material type that your toy is made up of.
How do I perform a flash test?
Flash tests like this for soft toys are not told in detail in the regulations as we’re using them under due diligence. What’s explained here would be good practise to show you’ve done your best, but it is down to you how far you take it, remember you’re aiming to prove as far as you can that your toy is compliant. If in doubt, perform the full test.
You perform a flash test in a similar way to testing a toy, as you want to be calculating the burn rate like you would a toy. In which case as toys for flammability are larger than 15cms, its best you choose a fabric sample minimum 15cmsx10cms to perform the tests on, and start the flame at 12cms from the top as you would on your toy.
Time how long it takes your sample to reach the top/or a certain marker point if it’s easier, and then calculate your burn rate as you would for your toy. If the burn rate is too fast (faster than 30mm/second) it could mean the fabric burns too quickly for a soft toy. However, the reason we test flammability on a completed toy is because a test on a toy is different to just burning fabric. Often with the addition of stuffing, and also after washing, it can burn slower, so don’t write it off completely without further investigation.
Flash testing other materials
It is possible to flash test knitted or crochet samples, just knit/crochet up a sample square and test as you would fabric, you could also test a stuffed sausage to get more of an idea of how your item burns with stuffing – you’ll still need to perform a fully flammability test on your completed toy though.
You may wish to document your flash tests in video or pictures, video you can take stills on is very helpful and can also help with the timing aspect.
Documenting your flash tests accurately and correctly could mean that it can be cross referenced in your files for other toys in the future.. saving you repeating the tests.
I must stress that its down to you the maker, to ensure you comply, so again if you’re not sure, do the full burn test.
and don’t forget to stay safe!

