Flammability for Head Toys

Flammability for Head Toys

Revision for “Flammability for Head Toys” created on 16 February 2021 @ 15:58:24

Title
Flammability for Head Toys
Content
[memberonly folder=“Basic,Community,Premium,Admin,Moderator"] While you may or may not wish to test flammability for your disguise costumes at home, it helps to know how it all works so that when it comes to design and also sending materials and costumes for flammability testing, you know what will pass or fail. Toys to be worn on the head understandably have a particular set of rules, due to the risk of them being worn whilst blowing out birthday candles for example. These particular rules are stricter on flowing items or elements of head wear which are flowing (dangling essentially) as they move when the head moves and are more likely to catch light and spread the flames. The tightness of the flammability rules increases the more the item sticks out/down from the head wear. When deciding what to test on your toy assess whether it has flowing parts, whether they measure longer than 5mm, less than 50mm or over 50mm. Then use the instructions to test each part according to what applies, this will involve several flammability tests to check each part of the head wear. (flowing elements, main fabrics, lining, other additions etc) and if your head wear includes other types, say a hat with mask, then each part needs to be tested according to the instructions set for that type of head toy. <strong>4.2 Toys to be worn on the head</strong> This applies to wigs,beards,hats, hoods, masks, headdresses etc Does not apply to paper/paperboard hats unless they have flowing elements If a toy has several different features (say hat with flowing elements) each should be tested to the relevant part. <strong>5.1.2 Before you start testing (conditioning)</strong> Toys should be kept for 7 hours at a temperature between 15-25oC humidity 60-70% <strong>5.4.1.1. Prepping samples in terms of washing</strong> prepare the samples as the toy would be sold, and as it would be washed So unwashed as sold, and then -however you would wash the item in the washing instructions (once) - or if no instructions/surface clean only following the immersion washing technique outlined in the guidance <strong>Flowing elements - beards moustaches and wigs, parts of head wearing toys which hang loosely</strong> Flowing elements are parts which of a toy worn on the head, which hang down which continue to move after the head is turned, these include things like hair, ribbons, long pile fabric etc over 5mm. - When checking measurements they should be measured without being pulled. -These are to be tested on a full toy sample with the flowing part vertical <strong>If the flowing element is under 5mm:</strong> then continue as for toys to be worn on the head (10mm/s limit) <strong>For flowing parts or pile over 5mm but under 50mm</strong> (also applies to full or partial moulded face masks but not eye masks/eye cheek masks) 5.3.3 Method: 20mm flame, positioned 45 degrees, toy vertical. Apply the flame for 5 seconds with the burner tube 5mm away so that the flame touches the toy 20-30mm above the bottom 4.2.3 The flowing part must stop flaming within 2seconds of the flame being removed, and the burn mark must not be more than 70mm. Calculate the burn rate by measuring the burn mark and dividing it by the amount of seconds it burnt for <strong>For Flowing elements or pile over 50mm(5cm)</strong> 5.2.1 Method: 20mm Flame, vertically applied hold the flame so it covers 1cm of the base of the flowing part for 2 seconds 4.2.2 the flowing part must stop flaming within 2s of the test flame being removed - it must not burn more than 50% If its over 150mm long -it must not burn more than 75% if its under 150mm long <strong>General Testing for Toys to be worn on the head</strong> for e.g anything not covered (or in addition to )in the flowing item tests, eye masks, eye and cheek masks, hats, hoods, etc etc is tested on samples from the costumes/head wear where possible. Your item may be too small for the samples stated in the regulations so we advise to use sample fabrics rather than exempt anything. <strong>5.4.1.3 Sampling for toys to be worn on the head, fabric eye masks etc</strong> (not beards or long pile/hair or full masks items(flowing elements) in 4.2.2 and 4.2.3) sample 610x100 of each material where possible cut vertically from as if the toy in use, preferably with no seams, or if needed seams in the upper part of the sample or if the sample size is too small you can use a joined sample of 2x 310 with a 10mm overlap stapled vertically for narrower items you can use the mesh to hold it. <strong>Preparing samples on rig:</strong> mount the samples onto the rig with a slight tension, the outside surface must be the upper facing for testing Position your marker threads across the width of the sample, 5cms from the top of the sample and 5cms from the bottom of the sample (if you are using the DIY rig affix this under the bulldog clips) using a weight of some sort to help indicate when the thread is burnt through. the rig should hold the fabric at a 45 degree angle 5.4.3/5.4.4 The burner flame should be 40mm high in a vertical position, 3cms from the bottom of the sample fabric Method: Apply the test flame for 10 seconds. If the fabric ignites start timing the burning when it burns the first marker thread. If the test fabric does not catch light after the 10 seconds, record: 'did not ignite' If the fabric flame goes out before the first marker, record: 'self extinguishes within 50mm of flame application' If the fabric self extinguishes between the first marker and the second marker thread(ie does not burn through second thread) record 'self extinguishing' and if the fabric burns through the second thread then work out the burn rate, and check it is within the burn rate expected: <strong>4.2.5 Toys to be worn on the head (except beards, long pile items,flowing items)</strong> -eye masks, hoods, head dresses with parts pointing upwards, 10mm/s maximum spread or should self extinguish
Excerpt


OldNewDate CreatedAuthorActions
16 February 2021 @ 15:58:24 CEmarkingAdmin
16 February 2021 @ 15:57:44 CEmarkingAdmin
16 February 2021 @ 15:56:58 CEmarkingAdmin
15 January 2021 @ 23:43:36 CEmarkingAdmin