Flammability for costumes

Flammability for costumes

Revision for “Flammability for costumes” created on 10 March 2021 @ 11:41:07

Title
Flammability for costumes
Content
<div class="kvgmc6g5 cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"> [memberonly folder=“Basic,Community,Premium,Admin,Moderator"] <strong>You may want to test your flammability for costumes at home, or send them for a lab test (cheapest test in the lab generally) but hopefully this run down of en71-2 for general costumes may help (see separate wiki for toys for the head) Don't forget our blog post on making a rig: <a href="https://www.cemarking-handmadetoys.co.uk/diy-flammability-test-rig-for-disguise-costumes/">here</a></strong> <strong>5.4.1.2.1 Sampling for disguise costumes</strong> </div> <div dir="auto">Take a sample from each material used on your item</div> <div dir="auto"> Functional strings or elastic not to be tested </div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"><strong>General samples info:</strong></div> <div dir="auto">Samples should be cut vertically from your sample toy where possible (as in if it was to catch light from the bottom and burn upwards)</div> <div dir="auto">Where fabrics are bonded (glued or sewn) samples can be cut and tested as bonded.</div> <div dir="auto">When possible always use the lower edge of the costume for the bottom of the sample to simulate the costume catching fire from the bottom as a general rule do not test samples with seams and trims aside from bottom edged ones, unless you are specifically testing embellished costumes (in which case we would say test both, parts with and without if its relevant) It is acceptable to use samples of fabric instead of cut from an actual toy.</div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto">NOTE: we would recommend when samples are difficult to take from smaller items(masks,crowns etc) to use samples of fabric rather than just exempting them, as over testing is better than under testing always, if you decide to do this, always test as close to the final piece as possible as extra as well as testing samples (so bonded fabrics, or with interfacings etc as well as samples)</div> <div dir="auto"> sample size: 600x100mm </div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"><strong>5.4.1.2.6 Costumes with fillings and features (applique, wadding, trims, embellishments,lace etc)</strong></div> <div dir="auto">If your item has a feature of some sort (applique,seam, etc) this should be central in your sample.</div> <div dir="auto">Your lower edge must be representative of the lower part of your item or end of sleeve (so if it has a lace bottom etc it catches light first)</div> <div dir="auto">vertical seams must be placed central in the sample</div> <div dir="auto">take a sample 610x100mm vertically from your costume toy</div> <div dir="auto"> if there isn't enough fabrics for this take a half sample 310x100mm vertically from the toy </div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"><strong>For parts of the costume with smaller amounts of fabrics (5.4.1.2.3 - 5)</strong></div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto">If your sample toy isn't big enough/doesn't contain enough of a certain fabric for a one complete vertical fabric sample, you may make a combined fabric sample, but your aim is to cut vertical pieces vs horizontal. You may cut fabrics in a 50/50 split or 75/25 with the larger sample at the bottom.</div> <div dir="auto">Ensure when using a joined fabric sample</div> <div dir="auto">- use vertical cut fabrics far as possible</div> <div dir="auto">-if this is not possible use vertical cut samples for the bottom of the sample, and horizontal for the upper part</div> <div dir="auto">-attach the two samples overlapping 10mm and fix with vertical staples, 5 equally distanced.</div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto">If your costume toy does not have enough fabric for this you can:</div> <div dir="auto">-make a half size complete sample at: 310x100</div> <div dir="auto">if it still doesn't have enough fabric for this</div> <div dir="auto">- you can make a half sized joined fabric sample:310x100mm</div> <div dir="auto">if there is not enough material to complete a halfsized joined fabric sample it is exempt. (Note: we recommend just using a fabric sample of the fabric used rather than exempting anything as over testing is preferred)</div> <div dir="auto"></div> <div dir="auto"><strong>5.4.1.2.7 For Narrower parts of a costume</strong></div> <div dir="auto">If the fabric is not wide enough for full samples you can use the mesh to test narrower samples of fabric 310x40mm vertical samples with no embellishments/seams</div> <div dir="auto">If you don't have enough for a 310x40mm sample it is exempt from testing (or test a fabric piece preferably)</div> <div dir="auto">Mesh: 18mm(plus or minus 4mm) squared with wire of 1mm (plus or minus 0.4mm)</div> <div dir="auto"></div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"><strong>5.1.2 Before you start (conditioning)</strong></div> <div dir="auto"> Toys should be kept for 7 hours at a temperature between 15-25oC humidity 60-70% </div> </div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"><strong>5.4.1.1. Prepping samples in terms of washing</strong></div> <div dir="auto">prepare the samples as the toy would be sold, and as it would be washed and dried</div> <div dir="auto">So unwashed as sold, and then</div> <div dir="auto">-however you would wash the item in the washing instructions (once)</div> <div dir="auto"> - or if no instructions/surface clean only following the immersion washing technique outlined in the guidance </div> <div dir="auto"><strong>5.4.2 Position of samples on the rig </strong>mount samples on the rig with the outer fabric facing up and with slight tension. Attach threads across the samples,threading a washer or similar on as a visual support as to when the threads burn through, at 5cm from the top of the sample, 5cms from the bottom of the sample and the midway point between them. <strong>5.4.3 Test Flame height should be 40mm (4cms) for general disguise toys </strong><strong>5.4.4 Place the burner vertical for general disguise toys</strong><strong>5.4.5 Performing the tests</strong>Apply the flame to the bottom of the sample for 10seconds. If flaming happens, start timing when the first marker burns through and stop when it burns through the second marker. <strong> </strong>If it does not catch light in those 10 seconds write: did not ignite If the sample self extinguishes before the first thread is burned through first marker write: self extinguished within 50mm If the sample burns through one marker but not the second write : self extinguishing If the second marker is burnt though then calculate the burn speed </div> </div> <div dir="auto"></div> <div class="o9v6fnle cxmmr5t8 oygrvhab hcukyx3x c1et5uql"> <div dir="auto"><strong><strong>4.3 Limits for Toy disguise costumes or items to be worn in play (not head wear) Remember speed= distance/time </strong></strong>Disguise toys with stuffing which could fall out should not burn faster than 30mm/sfor all other costume parts they should burn no faster than 30mm/s but if they are faster than 10mm/s then needs a 'Warning: keep away from fire' warning on permanent labelling and packaging. <strong>For stuffed parts of costumes: wash as you would for disguise costumes above. Then perform tests as per the soft toy instructions in the guide</strong></div> </div>
Excerpt


OldNewDate CreatedAuthorActions
10 March 2021 @ 11:41:07 CEmarkingAdmin
10 March 2021 @ 11:40:06 [Autosave] CEmarkingAdmin
10 March 2021 @ 11:38:56 CEmarkingAdmin
10 March 2021 @ 11:36:59 CEmarkingAdmin
10 March 2021 @ 11:34:44 CEmarkingAdmin
10 March 2021 @ 10:40:54 CEmarkingAdmin